Whirlpool Cabrio Washer Bearing Replacement: A Step-by-Step Guide for DIYers

Replacing the bearings in your Whirlpool Cabrio washer can be a challenging task, but it's one that can save you hundreds of dollars in repair costs. If you're up for the challenge, here's a step-by-step guide to help you get the job done right.

Tools and Materials You'll Need:

New bearing and seal kit

Socket wrench set

Screwdriver set

Pliers

Hammer

Pry bar

Bucket

1. Gather Your Tools and Materials

The first step is to gather all of the tools and materials you'll need for the job. This includes a new bearing and seal kit, a socket wrench set, a screwdriver set, pliers, a hammer, a pry bar, and a bucket.

Tool	Purpose
Socket wrench set	For removing the bolts that hold the tub in place
Screwdriver set	For removing the screws that hold the pump in place
Pliers	For removing the hoses that are connected to the pump
Hammer	For knocking the old bearings out of the tub
Pry bar	For prying the old bearing seal out of the tub
Bucket	For catching the water that will drain from the tub when you remove the pump

2. Disconnect the Water Supply and Power to the Washer

Before you begin working on the washer, it's important to disconnect the water supply and power. To disconnect the water supply, turn off the water valves that are located behind the washer. To disconnect the power, unplug the washer from the electrical outlet.

Safety Precaution	Purpose
Disconnect the water supply	To prevent flooding
Disconnect the power	To prevent electrical shock

3. Remove the Back Panel of the Washer

The next step is to remove the back panel of the washer. To do this, remove the screws that are located around the perimeter of the panel. Once the screws are removed, you can pull the panel off of the washer.

Step	Purpose
Remove the screws	To detach the back panel
Pull the panel off	To access the internal components

4. Remove the Drive Belt

The drive belt is located around the pulley of the motor. To remove the drive belt, use a pair of pliers to loosen the tensioner pulley. Once the tensioner pulley is loose, you can slip the drive belt off of the pulley.

Step	Purpose
Loosen the tensioner pulley	To release the tension on the belt
Slip the belt off the pulley	To remove the belt

5. Remove the Motor

The motor is located at the bottom of the washer. To remove the motor, remove the bolts that are holding it in place. Once the bolts are removed, you can lift the motor out of the washer.

Step	Purpose
Remove the bolts	To detach the motor
Lift the motor out	To remove the motor

6. Remove the Tub

The tub is located inside the washer. To remove the tub, remove the bolts that are holding it in place. Once the bolts are removed, you can lift the tub out of the washer.

Step	Purpose
Remove the bolts	To detach the tub
Lift the tub out	To remove the tub

7. Remove the Old Bearings and Seals

The old bearings and seals are located inside the tub. To remove them, use a hammer and a pry bar to knock them out of the tub.

Step	Purpose
Use a hammer and pry bar	To remove the old bearings and seals

8. Install the New Bearings and Seals

The new bearings and seals are located in the bearing and seal kit. To install them, use a hammer to tap them into place.

Step	Purpose
Use a hammer	To install the new bearings and seals

9. Reassemble the Washer

Once the new bearings and seals are installed, you can reassemble the washer. To do this, follow the steps in reverse order.

Step	Purpose
Reinstall the tub	To place the tub back into the washer
Reinstall the motor	To install the motor back into its place
Reinstall the drive belt	To put the drive belt back onto the pulley
Reinstall the back panel	To secure the back panel

10. Test the Washer

Once the washer is reassembled, test it to make sure that it's working properly. To do this, plug the washer into the electrical outlet and turn on the water supply. Then, run a test cycle to make sure that the washer is filling, draining, and spinning properly.

Step	Purpose
Plug in the washer	To restore power
Turn on the water supply	To allow water flow
Run a test cycle	To verify functionality

Whirlpool Cabrio Washer Bearing Replacement: A Step-by-Step Guide for DIYers